How long is the running-in period of Honda Wei Wu 1 10s?
Then slowly accelerate, and control it below 60 before 800 km, and control it below 80 from 1000 km to 1500 km. 1500 km
/kloc-above 0/00, you can occasionally pull the highway, but it can't exceed 2 minutes, and you can drive at will above 3000 kilometers.
Change the oil at 300, 800 and 1500 km, add mineral oil at 1000 km, and add semi-synthetic oil at 1200 km.
If it is changed, it will be changed to 1500~2000 km for total synthesis.
Matters needing attention during the running-in period are as follows:
(1) During the running-in period, drive in strict accordance with the gear and speed specified in the mileage stage, and use qualified fuel and lubricating oil.
For motorcycles with mixed lubrication, mixed oil should be prepared according to the requirements of the manual. Choose a smooth road with less dust.
When driving, try to avoid high-speed climbing and rapid acceleration. When driving, always change the engine speed, and don't fix it.
Continuous operation at a certain speed ensures the balanced stress of all parts and is conducive to the running-in between all parts. Shift gears should be timely and gentle, no
The vehicle needs to be throttled or braked urgently.
During the running-in period, in order to avoid the engine running at low speed (light load) for a long time, people can engage in various gears (the scooter can be appropriately increased).
Throttle opening) to accelerate the engine. Be careful not to exceed the specified maximum speed and the maximum speed limit of 125 ml for riding a motorcycle.
See table 4- 1 for the speed. The maximum throttle cannot be used within the initial 1000km.
(2) During the running-in period, let the engine have enough idle running time (3- 4) before starting in hot or cold state.
5min) Preheat to make the oil flow to all lubricating parts. Start driving at a low speed for a certain distance (1-2km), and then
Turn to normal driving. In hot season, the vehicle should stop and rest every time it travels 15-20km, so as not to cause the engine.
Overheating will dilute lubricating oil, reduce Hz, and form dry friction between moving parts, resulting in burning of cylinder and bearing.
Therefore.
(3) If there is a speed limit tube on the carburetor, it will affect the acceleration performance of the vehicle, but it is forbidden to disassemble it during the running-in period. Infinite speed loading
Don't turn the throttle to the full.
(4) All lubricating points should always be well lubricated.
(5) Fasteners of new cars are easy to loosen. Always check the fasteners. If it is loose, tighten it in time. If you find it while driving,
When air leakage, oil leakage and other faults occur, they should be repaired and eliminated in time.
(6) During the running-in period, the vehicle must complete the first maintenance project within 1000km. After the vehicle has traveled to the mileage specified in the manual,
The air filter should be cleaned; Replace the crankcase and transmission lubricating oil, and lubricate all lubricating points as required; Clean the spark plug
Carbon deposition, check the connection of all control wire ropes of the whole vehicle, and make adjustments if necessary; Check and adjust the braking device; Check and tighten
Tighten the fastening screws and nuts of all exposed parts; Check the tightness of the drive belt or chain; Check the tire pressure, and check it in time if necessary.
Expansion.
(7) After the running-in period of motorcycle expires, clean the air filter, fuel tank and its switch, filter screen, carburetor, oil pipeline, etc. And use pressure.
Compressed air blows through the pipeline to ensure smooth flow; Check and replace the lubricating oil of crankcase and transmission; Remove carbon deposits from spark plugs, and
Adjust the electrode gap; Remove carbon deposits on cylinder head, piston, piston ring and ring groove; Check and adjust the contact clearance of the circuit breaker; Check,
Adjust all control wire ropes of the whole vehicle; Check the hand brake shoe of clutch friction plate and replace it if necessary; Check the light, pull
Whether the buzzer works normally, and if necessary, adjust, check and adjust the tightness of the front fork lifter bearing; Check and tighten all exposed parts.
Fasteners; Carry out supplementary lubrication on the lubrication points of the whole vehicle; Four-stroke motorcycle engines should also check the intake and exhaust valves and valve clearance.
After the motorcycle running-in period expires, it is still not suitable to drive at high load or high speed for a long time, let alone on roads with particularly poor conditions. Generally speaking,
Generally speaking, it still needs a transition period of about 1000km.