Steps and specific methods of wallpaper pasting
Precautions before construction: wallpaper should be constructed after carpentry, painting, electricity and plastering. Otherwise, due to the large dust, it is easy to be polluted by organic solvents, which will affect the mounting quality and damage the wallpaper. The construction wall must be smooth and clean, with the same color, without delamination and dirt. Eight steps of how to paste wallpaper. 1. Check the wallpaper. Check whether the model of wallpaper is the same as the customer's order. Check whether the batch numbers of wallpaper are exactly the same. Try to use the same batch of wallpaper in a room, and never allow different batches of wallpaper to be posted on the same wall. Second, measure the length and height of the wall, and determine whether the amount of wallpaper purchased by customers is enough according to the actual pasting method and decorative effect of wallpaper. Third, the mixing of rubber powder is not random, and it should be properly mixed according to the type of wallpaper, the water absorption rate of the wall and the indoor temperature. Leave a certain amount of water in a clean plastic bucket, stir with a stick, pour in rubber powder, and blow for about 15 minutes.
Fourth, make vertical lines or horizontal lines. First of all, in the front of the room, press the wallpaper width to the indoor corner. The external angle should be wrapped (plastic external angle can be used), and the internal angle should overlap. Play a vertical line or a horizontal line according to the divided picture as the baseline for wallpaper pasting. 5. Cutting wallpaper According to the pattern design and decorative effect, wallpaper can be divided into three types: staggered flowers, parallel flowers (left and right flowers) and staggered flowers: 1. When cutting out the misplaced wallpaper, you only need to measure the height of the wall. The length of the wallpaper is about 3-5 cm higher than the wall, and it can be cut in the same direction. Note that those with significant pattern features should be cut from the top of the pattern; 2. When cutting the left and right wallpaper, first cut the first one according to the method of not cutting flowers, align the edge of the second wallpaper to be cut with the first one, so that the format, color and pattern are completely coincident with the first one, and then cut off the redundant part. Cutting a plurality of sheets of paper as a second sheet of paper; 3. When cutting the wallpaper with staggered flowers, cut the first one according to the method of staggered flowers, move the width pattern of the second one and the first one by half a symmetrical pattern, align them up and down, and cut off the redundant parts. The wallpaper pattern of the third picture is exactly the same as the first picture, the fourth picture is exactly the same as the second picture, and so on. Sixth, the thickness of glue depends on the type of wallpaper, the thickness of glue solution, the water absorption of wall surface and the indoor temperature. Spread the glue evenly with a sizing machine. Finally, the rubber surface is folded with the edges aligned, and then rolled into a tube for pasting.
Seven, when pasting wallpaper, you can use the instrument to judge the horizontal and vertical wallpaper, pay attention to the margin of the upper and lower edges. When laying wallpaper, pay attention to timeliness. If the glue starts to dry and harden, don't lift the wallpaper to correct it. 8. Clean and check the glue at the seams or in the middle of the wallpaper. Dip the glue gently with a wet towel, and don't wipe the wallpaper surface with a dry towel to remove the glue, which will ruin the wallpaper and fade. Notes on wallpaper pasting 1. In order to achieve the desired effect, this product must be stuck on the surface of smooth objects, and the solid surface must be dry and free of dirt such as mold and grease. If you want to paste wallpaper on a rough surface, the first step is to smooth it with sandpaper and clean it with water or neutral detergent to avoid affecting the use effect. 2. According to the size of the surface of the object you want to paste, cut out the product with the corresponding size. It is best to leave a distance of about 5cm.
3. Tear the film off the backing paper, pull the film forward with one hand, and flatten the film surface with the other hand from both sides of the image. It's easier to flatten with a soft cloth. 4. At the beginning, I suggest you stick it from top to bottom along the wall, and gently accumulate bubbles and wrinkles from Zhong Jian to both sides. Large bubbles can be punctured with needles to squeeze out air.
This answer comes from the user's original art villa, more decoration strategies and home experience. Welcome to the live APP.