What is the method of tying the main line with the eight-character ring?

1, passing through the rim, and one of them turns 4-5 times.

2. Take the first lap again.

Put it back to the big outer ring you just walked through.

4, tighten, just cut off the excess thread.

Binding method of nep 1:

1, the green line represents the main line, and the pink nylon rope represents the cotton line, as shown in the following figure.

2. Wrap the top cotton thread from the top of the main line to the bottom of the main line, pass through the cotton thread ring, and then turn to the top of the main line.

3, so repeatedly wear 5-6 laps.

4. First, slowly tighten the cotton thread on the left.

5. Then tighten both ends of the cotton thread, leaving about 0.5 cm in the middle. Just cut off the excess thread: be careful not to tighten it too tightly, because the cotton thread will tighten again when it meets water. As for how hard to tighten this, you have to master it yourself slowly. Sometimes you can burn the thread end with a lighter to prevent the thread end from loosening. Be careful not to hurt the main line.

The second way to play cotton knots:

1. Prepare a main thread and a section of cotton thread, with the green line representing the main thread and the white shoelaces representing the cotton thread.

2. First tie a knot on the main line with cotton thread and tighten it properly.

3. Both ends of cotton thread cross on the main line once.

Then wrap the two ends of cotton thread around the main thread and cross it again.

5. Wrap both ends of the cotton thread around the main thread and cross it again.

6. Continue to wind both ends of the cotton thread around the main line and cross it again.

7. Wrap the cotton thread on the main thread repeatedly, and cross it 6- 10 times.

8. Try to tighten the upper cross cotton thread around the main line, and then tie a fast knot to fix it.

The third way to play cotton knots

1. Wrap the cotton thread on the main line as shown in the figure.

2. Then thread the right thread under the main thread, and then thread the thread inward through the newly wound coil.

3. Continue to thread the right thread under the main line, and then pass through the newly wound coil. Please refer to the diagram for detailed steps.

4. Repeat this for 5-8 times.

5. Then slowly tighten the threads on both sides, leaving about 0.5 cm, just to cut off the excess threads.

The main junction connects the 8-character ring 1:

1. First tie a knot at one end of the main line, with white shoelaces representing the main line and green lines representing the eight-character ring.

2. Thread the knotted end into the 8-shaped ring.

3. Wrap the knotted thread around the main line.

4. Turn right again

Tie a fast knot

6. Slowly tighten the fast knot to the top of the first fast knot

7. Then slowly tighten the main line to the 8-ring.

8. The main line is connected with the 8-character ring.

The main line connects the 8-character ring 2:

1. The main line is folded in half by about 10cm, and then passes through the eight-character ring.

Step 2 wear it under the main line

3. Thread the coil into a fast knot

4. Tighten the fast knot, and then put the eight-character ring into the coil on the right.

5. Put the figure-eight ring into the coil and turn it to the right.

6. Turn the coil to the fast knot.

7. Tighten the two threads

8. Tighten the knot and cut off the short head.

The sub-line connect that rings of figure 8:

1. Knotted white shoelaces represent sub-lines, and green lines represent splayed rings.

2. The knotted end of the sub-wire passes through the splayed ring.

3. Thread the knotted end under the auxiliary line.

4. Make another turn around the secondary line.

5. Then thread the coil around the 8-character ring to form an 8-byte.

6. Slowly tighten the 8-character knot of the sub-line until the knot is dead, and the sub-line is connected with the 8-character line.