China Naming Network - Eight-character fortune telling - Installation method of folding door in bathroom Matters needing attention in the installation of folding door in bathroom

Installation method of folding door in bathroom Matters needing attention in the installation of folding door in bathroom

When decorating the bathroom, the door is indispensable. When choosing this kind of indoor door, folding door is a kind that everyone likes. After choosing such an indoor door, everyone needs to know the installation problem, so what should be paid attention to when understanding the installation of the folding door in the bathroom? Let's take a look at the installation method and installation precautions of the folding door in the bathroom with everyone.

Installation method of folding door in toilet

1, determine the location. First, determine the installation position before installing the folding door. If used as a kitchen door or bathroom door, it should be installed in the middle of the door frame; If it is used as the partition of the living room, it is necessary to determine the position, set aside the corresponding space and measure the straight line length. Then confirm whether the length of the track is correct. If the track is very long, measure the length with a ruler, mark it well, and cut off the long part with a hacksaw. Be careful not to let iron filings fall into the track, so as not to affect the sliding of the door.

2. Insert the folding door. Pick up the slideway, insert the folding door into the slideway in a tied state and push it to the middle of the slideway. The binding state is more convenient for installation, and it is pushed to the middle to prevent it from accidentally slipping off the slide way during installation.

3, fixed. Before fixing, determine the direction of the handle. If you are used to pulling it left or right, choose the corresponding direction according to your habits. After confirmation, start to install the track, and install it in the order of middle first and then sides. Screw screws into rails, doorframes or walls with an impact drill. Because the door frame or wall is thick, it is difficult to screw in the screws simply with a screwdriver, so it is necessary to use the power of an impact drill. After installing the screws, untie the rope that binds the folding door.

4. Press in the rubber sleeve. Open the folding door, compare the position of the magnet on the door, and determine the position where the magnet is installed on the wall or door frame. After determining the position of each suction plate, drill holes to a depth of about four centimeters with an impact drill, then drive the rubber sleeves into the holes, and then drive the rubber sleeves in turn.

5. Fix the suction cup. Push the folding door to the middle again, pick up the iron plate, align the hole on it with the center of the rubber sleeve hole, and screw the screw into the rubber sleeve with a screwdriver until the iron plate is fixed. Fix each sucker with the same steps, then open the folding door and suck the side without handle with the sucker. So a folding door was installed.

Matters needing attention in installing folding doors in toilets

1. Push the toilet folding door into the door opening as a whole, set the front and rear positions, fold the door leaf in the middle of the door frame, and screw several support screws beside the door frame to fix the upper wall and side wall of the door frame. Aim the impact drill at the upper, middle and lower holes of the left and right door frames, punch a hole with a diameter of 5mm in the inner wall of the door opening, and the depth is about 10mm, then loosen the support screw and take the toilet folding door out of the door opening.

2. Align an impact drill with a diameter of 7 mm with a wall hole with a diameter of 5 mm in the doorway, enlarge the hole with a diameter of 7 mm to a depth of about 40 mm, and then drive six rubber sleeves into the hole. Push the toilet folding door into the door hole again, find the center of the rubber hole, screw the self-correcting screw into the rubber sleeve hole with a screwdriver, and fix the door frame. Finally, open the door leaf of the toilet folding door in the middle of the door frame, tighten the clamping block screw of the hanging wheel above the toilet folding door with screws, insert the splint into the lower shaft of the toilet folding door, and tighten the screws.

Installing folding doors in the bathroom can not only save indoor space, but also be particularly beautiful. When choosing such an indoor door, the householder needs to know how to install it correctly. The above is the installation method and installation precautions of toilet folding door introduced by Bian Xiao. Here it is.