How big is the average bedroom door?
There are standard and non-standard sizes, usually standard and non-standard sizes. It is usually used in the process of finished doors and finished door cases. The construction process is based on the size of the door to determine the base layer of the door case, such as Anyang and Zhubiao products. There are also non-standard ones where you can make the door cover first, and then determine the size of the door according to the size of the door cover. Currently, the generally accepted bedroom door size is 80CM wide by 2 meters high.
The general standard room door size is 80CM wide by 2 meters high. When developing real estate, developers will reserve a space slightly higher than this size by more than ten centimeters or twenty centimeters. Some owners design their own houses.
Therefore, the size of the door is not determined from the beginning and can only be designed according to the actual standard. If the size of the bedroom door is too high, it can be filled to a value close to the standard. But in actual life, it is still necessary to go to the owner's home to measure the size and then design the size of the bedroom door.
Bedroom door (room door)
General bedroom doors are basically around 750-800MM. If the owner of the household is relatively tall, or is a foreigner from the north, consider the width. For 800-850, this is a more user-friendly design.
Extended information
The national standard for indoor doors is 860mmx2050mmx240mm. Single-open door (the first door when entering your living room)
General It is about 850-1000MM (MM=mm). The width of the door is a little more generous, giving people a more generous and decent feeling.
Double and double doors (one larger and one smaller)
Generally, the total width is about 1050-1200MM, the sub-door is about 300MM, and the rest is for the main door.
This makes it easier to move in and out when transporting large furniture.
Bedroom door (room door)
General bedroom doors are basically around 750-800MM. If the owner of the household is relatively tall, or is a foreigner from the north, consider the width. For 800-850, this is a more user-friendly design.
Kitchen door
Generally, kitchen doors are mostly sliding doors, which can be single push or double push and pull.
The total width of the door ranges from 1400-1800-?2000MM, which are all within the allowed range.
If it is a single opening, you can consider the width of 700-800MM for design. Because refrigerators and home appliances, some sizes and widths are already 600MM.
Toilet door (toilet door)
The door in this place can be slightly smaller, and it is mostly designed to be 550-600MM wide.
Specifications and dimensions:
1. Door opening dimensions
The door opening dimensions should comply with the regulations of GB/T 5824 — 1986. Recommended 700㎜×2000㎜, 760㎜×2000㎜, 800㎜×2000㎜, 900㎜×2000㎜, 700㎜×2100㎜, 760㎜×2100㎜, 800㎜×2100㎜, 900㎜×2100㎜, 1200 9 sizes including ㎜×2100㎜ are preferred.
2. Structural dimensions of the door
The structural dimensions of the door can be determined according to the decorative material of the door opening, the size of the attached frame, and the installation gap.
3. Thickness of door leaf
The thickness of door leaf is divided into 30㎜, 35㎜, 38㎜, 40㎜, 42㎜, 45㎜ and 50㎜. The thickness of the door frame (set) is determined accordingly according to the wall thickness.
The allowable deviation of wooden doors should comply with the following regulations:
1. The allowable deviation and inspection method of wooden doors
Frame and fan thickness +1.0 -1.0 Steel Check with ruler and micrometer
Frame height and width +3.0 +1.5 Check with steel ruler
Sash height and width -1.5 -3.0 Check with steel ruler
Frame , the diagonal length difference of the sash is 3.0, check with a steel ruler, measure the inside angle of the frame, and the outside angle of the sash
The height difference between the junction of the frame, sash section and the line is 1.0, check with a steel ruler and feeler gauge
p>
Fan surface flatness 2.0 Use a 1-meter ruler and feeler gauge to check
Fan warpage 3.0 On the inspection platform, use a feeler gauge to check
Frame front and side The installation verticality is 1.0. Use a 1-meter vertical inspection ruler to check
The height difference between the frame and the sash, and the sash and the sash is 1.0. Check with a steel ruler and feeler gauge
2. Seam limit Value
The gap limit for assembled wooden doors should comply with the provisions of Table 5.
3. Seam limit value and inspection method of wooden doors
Unit is millimeter
Inspection method of seam limit value of the project
There is a gap of 1.5~4.0 between the door leaf and the upper frame. Check with a feeler gauge
The gap between the door leaf and the side frame is 1.5~4.0
The gap between the door leaf and the ground is 4.0~6.0 for the outer door< /p>
Inner door 6.0～8.0
Bathroom 8.0～10.0
4. Decorative surface veneer surface appearance requirements
Pocket diameter 1㎜ Below (distance 300㎜) No limit to 2 or 5 pieces
The pitted surface has uniform particles and does not scratch the hand. No limit on hands
The scratch width is ≤ 0.5㎜ and the depth will not scratch the PVC decoration. The surface length is 100㎜, 3 strips, 1 strip and 2 strips
The depth of the indentation is ≤ 1.5mm, the width is less than 2mm, 8 pieces, 3 pieces and 6 pieces are not concentrated
The floating stickers are not firmly adhered Not allowed
Overlapping of wrinkled surfaces is not allowed
The missing skin area does not exceed 5㎡ 5 and 3 are not allowed
The raised skin does not exceed 2㎜ No limit to 5. Not allowed
The area of bright shadow/dark mark shall not exceed 50m㎡. No limit to 2 or 3.
The seam splicing gap shall not exceed 1㎜, shall not exceed 0.5㎜, shall not exceed 1㎜
5. Packaging
Each product should be packed with plastic film and packed in cartons. There should be a packing list and product inspection certificate inside the package.
6. Storage
Products should be stored in a clean, dry, well-ventilated warehouse with suitable humidity. The storage should be flat to prevent deformation
Reference materials ：Wooden Door-Baidu Encyclopedia