The last work of the new Jinxuan low-lying modification, the customized lounge chair and flange plate were officially opened.
Before I stopped the car, I ran to the store to get my recliner. The weight in your hand is still quite heavy, and the quality should be very good simply from the aspects of feel, appearance and weight.
This time, I changed the recliner on the rear wheel. Why should I change that? Just for posture. Many friends are asking what a recliner is. The reason why the rear wheel keeps a constant posture and angle is because the angle iron is fixed, so that the vehicle can keep the tire tread of the rear wheel completely in contact with the ground in the case of bumps.
This configuration can only be found on vehicles with independent suspension. Oh, that torsion beam model is not available. After I change this tilt angle, the wheels will show the effect of opening outward. Although the tires will have a certain degree of eccentric wear, the ultimate goal is to look good.
Well, if there is anything you don't understand, please read on and I'll explain it to you bit by bit. First, we have to remove the rear wheel hub. It's a professional refit shop. The jacks are all flat. I don't have to lift the car, so the jack can be put in. It's amazing.
This is what happens when the recliner is unpacked. Its main function is the two bolts here, and the final wheel angle can be changed by adjusting the bolts.
After the wheel hub is removed, the inclination angle of the original car can be removed. This screw has a fixed inclination angle, so it will be much clearer if you look at it from another angle. Needless to say, the tilt thickness of the original car is still very good. The visual inspection should be at least upward 1cm, which is not bad.
Little brother is hard enough. He just lies down to work. That's great. Yes, this is a comparison between the original car and my customized tendency. Obviously, the thickness and width of the tilt angle of the original car are better. It is really a conscientious enterprise that does not cut corners.
Let's install a new tilt angle. This adjustable position should be installed outside, which can facilitate the later adjustment.
There are not many angles set, only -3 degrees, because too many tires and wheels may rub against the wheel eyebrows, which is a bit of a loss. First load the car to see the effect, and compare it with the one I took before.
Isn't this angle obvious? The effect of the outer eight characters came out at once. Even if I put the wheel eyebrow on it, it doesn't seem to rub it. Perfect change is the effect I want.
Put it down and see. Maybe I didn't choose the right angle, but the effect can still be seen. Very handsome.
Friends who play pneumatic modification should know this, yes, it is flange, also known as gasket. This thing can be exquisite. After the wheel is splayed, the tire will not protrude, so in order to make the wheel hub flush with the car body, the gasket must be put in place, so that the effect is perfect.
Then continue, this angle is obvious, you can see that the angle changes greatly.
Remove the hub and continue to install the gasket. After all, you must confirm the inclination angle before you know whether the gasket is suitable.
Little brother suddenly got a stomachache in the middle of his work and deserted directly. This is really drunk. Then I will take some photos of the seats and steering wheel. The more I watch it, the more I like it. Friends who saw this post for the first time can look at my previous post, which contains detailed revision records.
My little brother has finally come back, and he has to continue his work. There is also a model on my washer. The above figures represent the hole spacing 5x 1 14.3, the central hole diameter 67. 1, and the thickness 15mm, which is installed on the right side. These data may be wrong, but if there is any mistake, the installation will fail.
This happened after the rear wheel of the original car was removed. Nowadays, cars are basically disc brakes, and drum brakes seem hard to see.
Try it on. Generally, the hole spacing of Japanese cars is 5x 1 14.3, German cars are 5x 1 12, and domestic cars are 5x 120. Please refer to the instruction manual or the markings on the wheels for details.
It really fits. In fact, the meaning of gasket is very simple, that is, to make the wheel more prominent, so this thing must be of excellent quality. For example, what I installed is a forgery, and the gasket of a pair of rear wheels costs four or five hundred yuan, also for safety.
It has been installed. This is the final effect. It still seems a little inside, doesn't it? However, New Jin Xuan itself has a small eyebrow. Even if this wheel eyebrow is not installed, it is necessary to cut the rear wheel eyebrow, which has certain security risks. I'd better choose insurance.
Actually, it looks very good. After all, it's -3 degrees, and the effect we want can still come out.
To celebrate the completion of the first phase of my new Jin Xuan, let's eat something good tonight. After all, this is a rare modification experience for me. I also hope that all modification enthusiasts will put forward more valuable suggestions and opinions, and I will accept them with an open mind. Thank you.