Installation method of electric shutter door Matters needing attention in installing electric shutter door

Electric shutter door is a kind of door that can be easily opened and closed, and it is a device with a large switch area. Mainly used in major shopping malls, garages or the facade of some businesses. It is both anti-theft and fire-proof. It is a low-cost door, so it is widely used now. So, what is the method of installing the electric rolling shutter door? What should I pay attention to when installing electric shutter doors? Now, Bian Xiao will introduce the matters needing attention and installation method of electric rolling shutter door for you in detail.

Installation method of electric shutter door

1: Prepare the installation tool. Operators should prepare tools and accessories such as electric welding machine, electric hammer, hand electric drill, ladder, drill bit, cutting head, spirit level and screwdriver.

2. Determine the installation size of the electric shutter door. The operator draws a line at the position of the door frame to determine the size of the electric shutter door, and then asks the construction personnel to make the electric shutter door with the appropriate size. Usually, the height of the electric shutter door is slightly higher than the door frame.

3. Determine the horizontal line and set the size according to the site conditions. The operator draws a horizontal line 50 cm above the hole in the side plate of the shutter door; Then draw a vertical line with a level at the position where the side panel of the shutter door steps out of the hole 13cm; Then put the auxiliary board 9 cm outside the door frame and draw a vertical line; Fix the side plate on the vertical line and draw a horizontal line at the highest point of the side plate.

4. The operator fixes the motor on the main board, then connects the roulette wheel with the motor base with a chain, and connects the remote control box device with the motor to test whether the handle of the shutter door is inverted. If the remote control receiving box of the electric shutter door is upside down, you need to push the built-in black button.

5: The electric shutter door is welded firmly. After the size of the electric shutter door is determined to be appropriate, it is welded firmly with the rotating shaft to keep the welded drill hole vertical. The operator should check whether the power supply of the electric shutter door works normally, draw the track of the shutter door into Chinese characters, level the shutter door to ensure the accuracy of the upper and lower horizontal lines, and then lift the curtain with the screw.

6. Inspection and testing. After the operator turns on the power supply, he pulls the switch of the electric shutter door to carry out the lifting demonstration operation, so as to ensure that there will be no failure and safety accidents. The operator ensures that the track of the electric shutter door is smooth and clean, and the button will not rebound and fail.

Matters needing attention in installing electric shutter doors

1. Draw a leader line at the position of the door frame to be installed. Indicate the size, and then ask the staff to design a suitable electric shutter door. It is worth noting that the height inside the frame is a little higher than that of the door leaf.

2. Fix the door frame of the electric shutter door first. Here, first remove the fixing plate at the lower part of the door frame. (Note: Grooves should be reserved on the ground on both sides of the hole. After correction, the wooden wedge should be fixed, and the iron foot of the door frame should be welded firmly with the embedded iron plate. With the strength of not less than 10MPa cement mortar or fine stone concrete plug. )

3. Install the main door leaf of the electric shutter. Make sure that the electric shutter door and the wall are integrated and sealed, and then paint the hole and the wall. After painting, the gap of the door should be even and smooth, and the electric shutter door should be opened freely and lightly, without being too tight, too loose and rebounding.

Above, Bian Xiao gave you a detailed introduction to the specific location of installing electric shutter doors, mainly at six o'clock. Although the operations are not many and complicated, we need to pay special attention to every point in the specific operation, because the success of the operation will affect the safety of the subsequent operations, so we need to pay attention to it. After work, the matters needing attention in installing electric rolling shutter doors are also introduced, which are ignored by some people. I hope consumers will pay more attention when installing.

Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~