China Naming Network - Almanac query - How to make a long cycad?

How to make a long cycad?

Question 1: How to make Cycas polycarpa have top advantages? Only by cutting off the top of the cycad can it grow into a cycad. It's just a long time. Sometimes only one head grows at the top after cutting, and then it needs to be cut again until two or three heads appear at the top of the cycad, which will grow more and more as time goes by. It usually takes two or three years. If the top decays naturally, the shape will be more ornamental.

Question 2: How to make a multi-headed cycad? In early spring, the normal growing point of Cycas was cut off, and then it was forbidden to spray water in the rain for a week or so. After that, the bull can germinate by strengthening the management of fertilizer and water.

Question 3: How was the long cycad cultivated? 1. Choose a good pot. Generally, deep flowerpots are not easy to use, while shallow Yixing purple sand pots are easy to use. Only in this way can we control the leaves and keep the bonsai shape.

Second, the soil. For the formed or basically formed Cycas bonsai, the soil is not easy to be too fertile, otherwise the leaves are not easy to control.

Third, turn off the sunlight. Cycas is a positive plant and should be placed in a sunny, warm and humid place with good ventilation. Control water before new leaves grow to prevent rain.

Fourth, cut the roots. The roots are lush and the leaves are lush. In order to control the leaves, the roots must be cut off to weaken the ability of plants to absorb water and fertilizer. Usually twice, once in the basin. Before germination. Cut off dead roots, diseased roots and over-dense roots, and cut short steep long roots.

Fifth, turn off water and fertilizer. Cycas are drought-tolerant and do not need floods. Not easy to get fat. Plants themselves have stored enough water and nutrients to meet the formation of new leaves. When new leaves develop, we should strictly control water and fertilizer, change watering into water spraying, and change fertilization into root fertilization to prevent rain forest.

Question 4: How to make an ordinary cycad into a multi-headed cycad? Cut off the tip (not the leaves) of the cycad with a sharp knife during the growing season. For example, one-third of the ball can be cut off and a multi-headed cycad can be born after re-germination. When the plant is large, it can be treated in the same way, but the potted ball is more ornamental.

Question 5: How to maintain the cycad bulls? With the introduction of Cycas bonsai into various offices, how to raise a large number of Cycas bonsai is a concern of teachers and staff. Now, I will discuss the basic knowledge of protection and management with teachers and staff. 1 is to turn off the sunlight. Cycas is a positive plant and should be kept in a sunny and well-ventilated place. Don't water the new leaves to prolong the sunshine time. The optimum temperature for the growth of Cycas is 24 -27 degrees. When the temperature is lower than 10 degree, the growth will stop. When the indoor temperature is below 0 degrees, it should be placed in a warm place to prevent frostbite. 2. Water and fertilizer should be properly controlled. Cycas is more drought-tolerant, but if it is too dry, its leaves will dim or wither, and in severe cases it will cause death. Generally, water once a week during the growing period. After autumn, control the water content. If it is white, water it more. If it is wet, don't water it. I remember it was too wet and rotten. Fertilization should use rotten cake fertilizer, and it is better to apply it once a month, and remember that the leaves can turn green and shiny, not too thick. It is necessary to control pests and diseases. There are fewer diseases and insect pests in Cycas, mainly including; Spot disease, scale insects and longicorn beetles. Spot disease is a fungal disease, which can be diluted with 50% Tobezin powder or potassium permanganate and sprayed. In the early stage of scale insects, cotton balls can be used to soak rice vinegar and gently rub the damaged leaves. If there is a hard shell, it can be scraped off with bamboo pieces, and in severe cases, the leaves can be cut off. If longicorn beetles are found, they can be captured manually.

Question 6: How to make multiple Cycas bonsai plants has top advantages. Only by cutting off the top of Cycas can we grow into multiple Cycas. It's just a long time. Sometimes only one head grows at the top after cutting, and then it needs to be cut again until two or three heads appear at the top of the cycad, which will grow more and more as time goes by. It usually takes two or three years. If the top decays naturally, the shape will be more ornamental.

Question 7: How to dig the heart, plant lobular iron and make bonsai plants all have top advantages. Only by cutting off the top of the cycad can it grow into a multi-headed cycad. It's just a long time. Sometimes only one head grows at the top after cutting, and then it needs to be cut again until two or three heads appear at the top of the cycad, which will grow more and more as time goes by. It usually takes two or three years. If the top decays naturally, the shape will be more ornamental.

Question 8: What happened to this cycad? Are there many bulls? All plants have top advantages. Only by cutting off the top of the cycad can it grow into a multi-headed cycad. It's just a long time. Sometimes only one head grows at the top after cutting, and then it needs to be cut again until two or three heads appear at the top of the cycad, which will grow more and more as time goes by. It usually takes two or three years. If the top decays naturally, the shape will be more ornamental.

Question 9: A cycad has two heads. How to become a long cycad is better, but both can be kept.